Porsche
>
993 (911) (1994-1998)
>
Engine Electrical
>
Distributor Cap
>
Distributor Cap Clamp Large. Porsche 911 1978-83 / 930 1975-89
Distributor Cap Clamp Large. Porsche 911 1978-83 / 930 1975-89 - 93060296500
Related products
Distributor cap. Porsche 964 / 993
Code: 93060291901
Distributor cap. Porsche 964 / 993
Two per car. Sold each.
Fits:
Porsche 964 1989-94
Porsche 993 09/1989 - 08/1997
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060291901
The product you are viewing cross references to these numbers
Two per car. Sold each.
Fits:
Porsche 964 1989-94
Porsche 993 09/1989 - 08/1997
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060291901
93060291901
1691200202
The product you are viewing cross references to these numbers
Product Vehicle Group
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
Price: €209.70
Orderable
Belt and Pin for Twin IGN Distributor. Porsche 964 1990-94 / 993 1995-97
Code: DISTKIT964
Belt and Pin or Twin IGN Distributor.
A design fault on engines up to August 1993 that you MUST fix if not already done so is to add ventilation to the distributor to prevent ozone perishing the distributor drive belt. If this breaks you will be running on one plug per cylinder and will end up with poor performance and possible damage.
The solutions is to also fit a Venting kit.
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
DISTKIT964
The product you are viewing cross references to these numbers
A design fault on engines up to August 1993 that you MUST fix if not already done so is to add ventilation to the distributor to prevent ozone perishing the distributor drive belt. If this breaks you will be running on one plug per cylinder and will end up with poor performance and possible damage.
The solutions is to also fit a Venting kit.
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
DISTKIT964
93060213400
93060292200
The product you are viewing cross references to these numbers
About this kit
This kit is comprised of the following items:
1 x DISTRIBUTOR GEAR PIN (93060292200
1 x DISTRIBUTOR DRIVE BELT (93060213400/1
Product Vehicle Group
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
€24.81
Now €23.57
In stock
Distributor Vent Kit. Porsche 964 1990-94 / 993 1995-97
Code: 00004320252
Distributor Vent Kit.
964 Ventilation Kit includes:
- Distributor ventilation connection (A)
- Rubber Grommet (B)
- White Grommet connector (C)
- Hose (D)
HOW TO FIT: Firstly prise of the oval plate arrowed on the distributor with a screwdriver. Then remove the large black air guide pipe as we need to drill a hole in it at the green dot. The pipe removes by loosening jubilee clips at top and bottom. You will also need to remove two sensor connectors on the pipe. I also removed the two sensors near the distributor so that I had easy access to the plate. Drill at 18mm hole in the pipe, 40mm to the right of the tail light ventilation nipple. Deburr the hole and remove all shavings. Install the rubber grommet (B) into the hole and install the white connector (C) into the grommet.Install the distributor connector (A) into the hole in the distributor where the plate was. Finally refit the air pipe and connect back up all the sensors. Install the hose (D) onto the new distributor and air pipe nipples and route
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
964 Ventilation Kit includes:
- Distributor ventilation connection (A)
- Rubber Grommet (B)
- White Grommet connector (C)
- Hose (D)
HOW TO FIT: Firstly prise of the oval plate arrowed on the distributor with a screwdriver. Then remove the large black air guide pipe as we need to drill a hole in it at the green dot. The pipe removes by loosening jubilee clips at top and bottom. You will also need to remove two sensor connectors on the pipe. I also removed the two sensors near the distributor so that I had easy access to the plate. Drill at 18mm hole in the pipe, 40mm to the right of the tail light ventilation nipple. Deburr the hole and remove all shavings. Install the rubber grommet (B) into the hole and install the white connector (C) into the grommet.Install the distributor connector (A) into the hole in the distributor where the plate was. Finally refit the air pipe and connect back up all the sensors. Install the hose (D) onto the new distributor and air pipe nipples and route
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
Product Vehicle Group
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
Price: €43.88
In stock